single groove
英 [ˈsɪŋɡl ɡruːv]
美 [ˈsɪŋɡl ɡruːv]
网络 单面坡口
双语例句
- Experimental Study on Single-Groove Heat Pipe
单槽缝热管的实验研究 - The evident bump back and sealing effect of single acting variable section groove seal were proved through the tests of bump back capability of the four hydrodynamic groove structure of rotary shaft lip seal.
通过对旋转轴唇形密封圈4种流体动力沟槽结构返油能力的试验研究，验证了单向变截面沟槽油封有明显的返油泵吸效应及其密封作用。 - Study on Stress Concentration for A Bending Plate with Single U Shaped Groove
单侧有U形槽弯曲平板应力集中的研究 - The testing results indicate that the penetration is increased 3 times compared with the conventional TIG welding and, for the plates of 12 mm thick, the fully penetration can be got in a single pass without groove preparation.
试验结果表明，使用本活性剂可使焊缝熔深比常规的TIG焊增加3倍，对12mm以下的低碳钢板对接无须开坡口，可一次焊接完成并能单面焊双面成型。 - On the basis of the study of the single circular groove guide and symmetric double circular groove guide, a new structure, asymmetric double circular groove guide, has been put forward.
本文在单个圆形槽波导和对称圆形双槽波导研究的基础上，提出了非对称圆形双槽波导。 - The steel with discontinuous flowline microstructure has lower grooving corrosion susceptibility and only single corrosion groove exists along the welding line.
而不连续流线组织的钢板具有较低的沟槽腐蚀敏感性，在焊缝处产生单腐蚀沟槽。 - The double radius ellipse pass is better than the one of single radius ellipse in the big round bar or big section steel rolling. It has some advantages, such as easy nipping, uniform deforming and small wearing of groove.
在大圆钢轧制或大断面轧件延伸孔型系统中，双半径椭圆孔型与单半径椭圆孔型相比，具有轧件易咬入、变形较均匀、孔型磨损小等优点。 - Improvements of the Subsidiary of Mechanical Seals With a Single End Helix Groove
单端面螺旋槽机械密封配套设施的改进 - Analysis for Uncertainty of Measurement of Single Groove Specimen Calibrating Device
单刻线样板检定装置测量不确定度分析 - The procedure parameters to keep smooth bead on both sides with single side welding for the sheet, groove size of backing, assembly gap, traverse tolerance between wire and workpiece are all determined by experiment.
通过工艺试验，确定了保证薄板单面焊双面成形、光滑均匀的工艺参数范围、背面垫板凹槽尺寸、工件装配间隙、焊丝和工件的横向偏差量等。 - However, the design of disk-type tool is complex. The usual solution is to compile the special computer program for calculating the tool profile of a single helical groove.
加工螺旋曲面用的盘状成形刀具的设计是一个比较复杂的过程，通常的解决办法是根据螺旋槽的设计参数编制计算铣刀廓形的专用计算程序来辅助铣刀的设计。 - Different amelioration measures on coastal saline soil have different effects. The effects of comprehensive amelioration measures are superior to single measure. The effects of carrying on land cover on the basis of digging deep groove combined with planting salt-tolerant plants are the best.
不同改良措施对滩涂土壤的改良效果不同，综合措施的改良效果优于单一措施。